EZ-Flash USA Forum

ryl3n · **Joined:** Tue Jun 30, 2009 5:45 pm **Posts:** 116

Quote:

2.Special mode speed setting- highest speed 0, lowest 10. Allows users with slower memory to set a speed.

how to change or configure speed? is it automatic?

Thanks

flastosh · **Joined:** Thu Dec 28, 2006 8:37 am **Posts:** 317

Well the DLDI is faster but apparently the homebrews support doesn't change.

Zurg · **Joined:** Fri Jun 11, 2010 8:18 am **Posts:** 4

i updated my ezvi with H705 but when I start Warioware DIY it display a save message that stays for hours ... I updated another ezvi but with H805 and warioware diy works ...

Jonez001 · **Joined:** Mon Jun 29, 2009 3:29 am **Posts:** 328

ryl3n wrote:

Quote:

2.Special mode speed setting- highest speed 0, lowest 10. Allows users with slower memory to set a speed.

how to change or configure speed? is it automatic?

Thanks

Look at the menu where you normally use cheats, you will see it there!

FAST6191 · **Posted:** Sat Jun 12, 2010 4:04 am

@DEagleson trimming a rom does not change it in the slightest (beyond the making it smaller thing)- assuming it is trimmed properly the only trouble you should run into is with a bad method of patching on a translation/trainer or something.

Zurg · **Joined:** Fri Jun 11, 2010 8:18 am **Posts:** 4

Zurg wrote:

i updated my ezvi with H705 but when I start Warioware DIY it display a save message that stays for hours ... I updated another ezvi but with H805 and warioware diy works ...

it's possible that I have used update 1.4 for H805 instead of the one for H705 ... now how can i go back if my dsi displays now: H705 101 3.0B1?

Mbmax · **Posted:** Sat Jun 12, 2010 5:45 am

Zurg wrote:

i updated my ezvi with H705 but when I start Warioware DIY it display a save message that stays for hours ... I updated another ezvi but with H805 and warioware diy works ...

it's possible that I have used update 1.4 for H805 instead of the one for H705 ... now how can i go back if my dsi displays now: H705 101 3.0B1?

Don't try to downgrade or whatever, your 705 is updated correctly in v101 if it's displayed in system menu.
Now your problem is tied to the microsd you use in it.
Backup it on your PC, format it and restore data expect ROMDAT folder.
Try again.

Save creation should take approx 38 secondes for 32MB file written.

Sata · **Joined:** Wed Sep 09, 2009 4:25 am **Posts:** 18

Mbmax wrote:

Save creation should take approx 38 secondes for 32MB file written.

WarioWare DIY? Because the first time I ran it on my EZ5i [705] it was on 3.0 OB1 and it took less than (or about) 10 seconds.

The Composer · **Joined:** Thu May 06, 2010 9:37 pm **Posts:** 8

I updated to the last firmware and kernel. Most AP games work without patching.

GTA Chinatown Wars does not work properly though.

ryl3n · **Joined:** Tue Jun 30, 2009 5:45 pm **Posts:** 116

Jonez001 wrote:

ryl3n wrote:

Quote:

2.Special mode speed setting- highest speed 0, lowest 10. Allows users with slower memory to set a speed.

how to change or configure speed? is it automatic?

Thanks

Look at the menu where you normally use cheats, you will see it there!

Thanks for the reply sir I figured it out earlier today, I didn't know that I have to touch the number beside the switch on/off to adjust the level :lol:

Drag0nflamez · **Joined:** Tue Apr 21, 2009 10:58 am **Posts:** 35

Why was the PassMe feature removed? If I press L while booting, it doesn't come up with that Passme thing.
though i dont use it, it would be intresting to know why

Zurg · **Joined:** Fri Jun 11, 2010 8:18 am **Posts:** 4

Mbmax wrote:

Zurg wrote:

i updated my ezvi with H705 but when I start Warioware DIY it display a save message that stays for hours ... I updated another ezvi but with H805 and warioware diy works ...

it's possible that I have used update 1.4 for H805 instead of the one for H705 ... now how can i go back if my dsi displays now: H705 101 3.0B1?

Don't try to downgrade or whatever, your 705 is updated correctly in v101 if it's displayed in system menu.
Now your problem is tied to the microsd you use in it.
Backup it on your PC, format it and restore data expect ROMDAT folder.
Try again.

Save creation should take approx 38 secondes for 32MB file written.

thanks for the answer...
Finally I was succesfull just following your advice but changing the microSD, same model (sandisk 4GB).

Jisatsu · **Joined:** Sat Jun 12, 2010 9:13 pm **Posts:** 1

So I have the EZVi with Kernel 3.0 OB1 and I upgraded the firmware to v101 and I am having problems.

Now for some reason I am unable to change the screen brightness. I press the L button, no effect. I press the brightness button in the EZFlash menu, no effect.

I've scoured this thread and checked on GBAtemp but no one has reported anything, so maybe its isolated to just mine.

This did not happen in the last RC version, and my L button is working, I checked in other games.

Hardware Specs:
Hardware Revision: H805
Firmware: 101
Nintendo DS Lite
EZFlash Vi

Cherube · **Joined:** Wed May 06, 2009 12:47 pm **Posts:** 12

3538 - Grand Theft Auto: Chinatown Wars (E) = black screens after save creation

Don't know if it has been reported but it works with special mode at speed 3

Hardware [805] with 4Gb Samsung class 4
Firmware v101 + Kernel 3.0OB1

Mbmax · **Posted:** Sun Jun 13, 2010 9:00 am

Cherube wrote:

3538 - Grand Theft Auto: Chinatown Wars (E) = black screens after save creation

Don't know if it has been reported but it works with special mode at speed 3

Hardware [805] with 4Gb Samsung class 4
Firmware v101 + Kernel 3.0OB1

I confirm this. thanks for your report.
Next time, please post it in the DS game thread.

BTW, speed 3 mean you must have a very good microSD with a good access time.
I will report that. The special mode need to be optimized i think.

EZ-Flash USA Forum

Kernel 3.0 OB1 and EZ5i firmware v101 (10th June 2010)

Who is online